WE offer effective protection

.

Instructions for use

BALTIC MASKS, UAB, Address: Savanoriu ave. 178F, 03154, Vilnius, Lithuania. Registration nr.: 305709371. VAT: LT100013839515

 

This product has been manufactured in compliance with Regulation (EU) 2016/425, for basic use, EN 149:2001+A1:2009 Respiratory protective devices. Filtering half masks to protect against particles. Requirements, testing, marking, in compliance with certificate; 1463 Polski Rejestr Statków S.A. al. gen. Józefa Hallera 126 80-416 Gdańsk, Poland

MODEL

BM-022H

BM-032H

CLASS

FFP2 NR D

FFP3 NR D

LAYERS

5

6

MEDIA

50gsm-SN

75gsm-FN

25gsm-MN

25gsm-MN

25gsm-SN

50gsm-SN

75gsm-FN

25gsm-MN

25gsm-MN

25gsm-MN

25gsm-SN

VALVE

No

No

SN - Spunbond Nonwowen Fabric

MN - Meltblown Nonwoven Fabric

FN - Filament Nonwoven Fabric

 

Instructions for use: 

 

Do not wear with beards or other facial hair that may inhibit contact between the face and edge of the respirator!

 

1. With reverse side up, separate top and bottom panels.

2. Pull the panels until the nose clip bends so that the respirator forms a cup shape. Ensure both panels are fully unfolded.

3. Hold the respirator with an open side towards the face and bring the respirator to the face.

4. Hold the cup respirator in one hand with an open side towards the face.

5. With another hand, take each strap in turn and pull each strap over your head.

6. Locate the upper strap across the crown of the head and the lower strap below the ears. Straps must not be twisted. Adjust the top and bottom panels for an adjustable comfortable fit. Ensure that panels are not folded.

7. Using both hands, mold the nose clip to the shape of the nose to ensure a close fit and good seal. Pinching the nose clip using only one hand may result in less effective respirator performance.

8. The seal of the respirator on the face should be fit-checked before entering the workplace.

Controls prior use:

Donning instructions to be followed each time you use the mask. Before use, check for visible damage, damaged or dirty (on breathing side) filtering half masks cannot be used.

 

Packaging: 1 / 2 / 5 / 10 pcs.

 

Fields of use applicable to this PPE: This PPE is intended for respiratory protection against particles, except particles for escape situations.

 

Levels or classes of protection offered by PPE intended for respiratory protection

 

Maximum penetration of the filter material (Paraffin Aerosols and Sodium Chloride):

CLASIFICATION

%MAX

FFP1 

20

FFP2 

6

FFP3

1

 

Breathing resistance

 

 

CLASIFICATION

Maximum permitted resistance (mbar)

Inhalation

Exhalation

30 I/min

95 I/min

160 I/min

FFP1

0.6

2.1

3.0

FFP2

0.7

2.4

3.0

FFP3

1.0

3.0

3.0

 

 

Total inward leakage

At least 46 of the 50 individual exercise result for total inward leakage (i.e. 10 subjects x 5 exercises) must not exceed:

25% for FFP1

11% for FFP2

5% for FFP3

Additionally, at least 8 of 10 arithmetic means of the individual carriers for total inward leakage must not be greater than: 

22% for FFP1

8% for FFP2

2% for FFP3

 

Marking and performance recorded in technical tests applicable to the PPE:

BM-022H FFP2 NR D. EN149:2001+A1:2009. CE1463. Baltic Masks Logo.

BM-032H FFP2 NR D. EN149:2001+A1:2009. CE1463. Baltic Masks Logo.

 

Marking meanings:

- Applicable standard

- Name or brand off the manufacturer

- PPE reference

- CE Marking + Notified Body of production control: CE 1463

- Classification: FFPX NR D, where:

‘’R’’: The particulate filter half mask can be used for more than one work shift.

‘’NR’’: the particulate filter half mask must not be used for more than one work shift.

‘’D’’: Clogging test with dolomite, if applicable.

 

Limitations of use

- Don`t use it against gases.

- The user must know the use and handling of the mask.

- Do not use in areas of risk of explosion.

- This PPE should not be used against risk other than those described.

- The filtering half mask should not be used more than one shift when it is marked “NR”, so it must be discarded.

 

Warnings:

- Check the fitting or adjustment of the filtering half mask before using.

- Tightness requirements are unlikely to be met if, under the facial seal, facial hair pass.

- Air quality must be considered (pollutants, oxygen deficiency).

- The use of the equipment in explosive atmospheres is not allowed.

- The mask does not require maintenance as it is a single-use PPE.

 

Useful life expiration: See the packaging

Manufacturing year:  See the packaging

Access to the Declaration of Conformity: www.balticmasks.com

 

PICTOGRAMS EXPLANATIONS

A picture containing text, monitor, screen, image

Description automatically generated View information provided by the manufacturer

Icon

Description automatically generated Year / month (expiration date)

A picture containing text, sign, close

Description automatically generated Temperature range of storage

A picture containing text, monitor, indoor, device

Description automatically generated Maximum relative humidity for storage - % RH

A picture containing text, monitor, sign, white

Description automatically generated Year / month (manufactured date)

A white and black sign

Description automatically generated with low confidence Lot number

A picture containing text, monitor, sign

Description automatically generated Manufacturer

A picture containing text, electronics, sign

Description automatically generatedHumidity range of storage conditions

Icon

Description automatically generated Do not damage the packaging

A black and white skull

Description automatically generated with low confidence Recyclable cardboard

Storage instruction: Keep the mask away from unnecessary exposure to sunlight, in dry places and protected against aggressive agents

BALTIC MASKS, UAB, Address: Savanoriu ave. 178F, 03154, Vilnius, Lithuania. Registration nr.: 305709371. VAT: LT100013839515

 

This product has been manufactured in compliance with Regulation (EU) 2016/425, for basic use, EN 149:2001+A1:2009 Respiratory protective devices. Filtering half masks to protect against particles. Requirements, testing, marking, in compliance with certificate; 1463 Polski Rejestr Statków S.A. al. gen. Józefa Hallera 126 80-416 Gdańsk, Poland

MODEL

BM-001

BM-026

BM-027

BM-027V

BM-031

BM-031V

CLASS

FFP2 NR D

FFP2 NR D

FFP2 NR D

FFP2 NR D

FFP3 NR D

FFP3 NR D

LAYERS

5

3

4

4

5

5

MEDIA

50gsm-SN

25gsm-MN

40gsm-HN

25gsm-MN

25gsm-SN

50gsm-SN

25gsm-MN

25gsm-HN

50gsm-SN

40gsm-MN

40gsm-HN

25gsm-SN

50gsm-SN

40gsm-MN

40gsm-HN

25gsm-SN

50gsm-SN

25gsm-MN

40gsm-HN

25gsm-MN

25gsm-SN

50gsm-SN

25gsm-MN

40gsm-HN

25gsm-MN

25gsm-SN

VALVE

No

No

No

Yes

No

Yes

SN - Spunbond Nonwowen Fabric

MN - Meltblown Nonwoven Fabric

HN - Hot air Nonwoven Fabric

 

Instructions for use: 



 

Do not wear with beards or other facial hair that may inhibit contact between the face and edge of the respirator!

 

1. Open the mask with both hands to the two sides.

2. Straighten the nose bridge stripe.

3. Fit the mask on your face covering the mouth and nose. The straps should not be between the mask and your face.

4. Pull the straps above your ears. Adjust the mask unƟl it fits comfortably.

5. Adjust the nose bridge stripe, until it completely fits to your nose bridge and you don't feel any air leakage.

6. Cover the mask with both hands until the mask fits tightly around the face.

Controls prior use:

Donning instructions to be followed each time you use the mask. Before use, check for visible damage, damaged or dirty (on breathing side) filtering half masks cannot be used.

 

Packaging: 1 / 2 / 5 / 10 pcs.

 

Fields of use applicable to this PPE: This PPE is intended for respiratory protection against particles, except particles for escape situations.

 

Levels or classes of protection offered by PPE intended for respiratory protection

 

Maximum penetration of the filter material (Paraffin Aerosols and Sodium Chloride):

CLASIFICATION

%MAX

FFP1 

20

FFP2 

6

FFP3

1

 

Breathing resistance

 

 

CLASIFICATION

Maximum permitted resistance (mbar)

Inhalation

Exhalation

30 I/min

95 I/min

160 I/min

FFP1

0.6

2.1

3.0

FFP2

0.7

2.4

3.0

FFP3

1.0

3.0

3.0

 

 

Total inward leakage

At least 46 of the 50 individual exercise result for total inward leakage (i.e. 10 subjects x 5 exercises) must not exceed:

25% for FFP1

11% for FFP2

5% for FFP3

Additionally, at least 8 of 10 arithmetic means of the individual carriers for total inward leakage must not be greater than: 

22% for FFP1

8% for FFP2

2% for FFP3

 

Marking and performance recorded in technical tests applicable to the PPE:

BM-001 FFP2 NR D. EN149:2001+A1:2009. CE1463. Baltic Masks Logo.

BM-026 FFP2 NR D. EN149:2001+A1:2009. CE1463. Baltic Masks Logo.

BM-027 FFP2 NR D. EN149:2001+A1:2009. CE1463. Baltic Masks Logo.

BM-027V FFP2 NR D. EN149:2001+A1:2009. CE1463. Baltic Masks Logo.

BM-031 FFP3 NR D. EN149:2001+A1:2009. CE1463. Baltic Masks Logo.

BM-031V FFP3 NR D. EN149:2001+A1:2009. CE1463. Baltic Masks Logo.

 

Marking meanings:

- Applicable standard

- Name or brand off the manufacturer

- PPE reference

- CE Marking + Notified Body of production control: CE 1463

- Classification: FFPX NR D, where:

‘’R’’: The particulate filter half mask can be used for more than one work shift.

‘’NR’’: the particulate filter half mask must not be used for more than one work shift.

‘’D’’: Clogging test with dolomite, if applicable.

 

Limitations of use

- Don`t use it against gases.

- The user must know the use and handling of the mask.

- Do not use in areas of risk of explosion.

- This PPE should not be used against risk other than those described.

- The filtering half mask should not be used more than one shift when it is marked “NR”, so it must be discarded.

 

Warnings:

- Check the fitting or adjustment of the filtering half mask before using.

- Tightness requirements are unlikely to be met if, under the facial seal, facial hair pass.

- Air quality must be considered (pollutants, oxygen deficiency).

- The use of the equipment in explosive atmospheres is not allowed.

- The mask does not require maintenance as it is a single-use PPE.

 

Useful life expiration: See the packaging

Manufacturing year:  See the packaging

Access to the Declaration of Conformity: www.balticmasks.com

 

PICTOGRAMS EXPLANATIONS

A picture containing text, monitor, screen, image

Description automatically generated View information provided by the manufacturer

Icon

Description automatically generated Year / month (expiration date)

A picture containing text, sign, close

Description automatically generated Temperature range of storage

A picture containing text, monitor, indoor, device

Description automatically generated Maximum relative humidity for storage - % RH

A picture containing text, monitor, sign, white

Description automatically generated Year / month (manufactured date)

A white and black sign

Description automatically generated with low confidence Lot number

A picture containing text, monitor, sign

Description automatically generated Manufacturer

A picture containing text, electronics, sign

Description automatically generatedHumidity range of storage conditions

Icon

Description automatically generated Do not damage the packaging

A black and white skull

Description automatically generated with low confidence Recyclable cardboard

Storage instruction: Keep the mask away from unnecessary exposure to sunlight, in dry places and protected against aggressive agents

 

 

 

 

Storage Conditions and Shelf Life: 

The medical disposable non sterile face masks must be stored in their packets to retain their properties. Shelf life of unopened product is 2 years from date of manufacture when stored within temperature range of -10°C to +40°C and of 20% to 85% relative humidity.


 

Usage instruction

 

 

Do not wear with beards or other facial hair that may inhibit contact between the face and edge of the respirator!

 

Donning instructions to be followed each time you use the mask. Before use, check for visible damage, damaged or dirty (on breathing side) medical face masks cannot be used.


 

  1. Before opening and touching the mask, wash your hands thoroughly with soap and water or alcohol/based hand sanitizer (>60% alcohol content).
  2. Open the mask with both hands to the two sides.
  3. Hold the mask by the ear loops. Place a loop around each ear and be sure the nose clip is upwarded.
  4. Press the nose clip to fit the shape of the nose
  5. Pull the bottom of the mask over your mouth and chin.

 

Precaution!

 
 

  1. This product is not suitable for protection against harmful gases, steam and oily aerosols.
  2. The product does not generate oxygen and is not suitable for use in anoxic environments, underwater operations, during evacuation or firefighting environments.
  3. It is not recommended to use this medical face mask if you do not feel a good adhesion between the face and the edge of the mask during use.
  4. If found during use that the mask is damaged or the breathing resistance is too large, replace with a new one.
  5. This product is for one-time use, masks should not be reused.


Warning! - this product is not flame resistant and must not be used in areas with open flames

 


 

 

         Manufacturer: BALTIC MASKS, UAB, Savanoriu ave. 178F, Vilnius, Lithuania 

                  Link to the declaration of conformity: www.balticmasks.com

 

 

 

 

EXPERIENCE AND SUPPLIERS

LOGISTICS

During more than 20 years of cooperation with the Far Eastern market and the organization of the supply of goods in the Baltic States, we have accumulated many years of experience. Experience allow us to guarantee reliability and security for our customers. We are happy to supply customers with high quality products. We manufacture goods or import them directly from the manufacturer, so we always offer products at the lowest price on the market.

In order to shorten the supply time of receipt products, we work with the strongest market leaders in this field, whose quality of service and work has never disappointed us. Cooperation based on trust and teamwork is a guarantee of quality. Together, we pursue a common goal - to supply and transport goods at the lowest market price.

CONTACT US

“Baltic Masks” sales team is in a stage of active search of authorized partners all over Europe, who could work in the name of “Baltic Masks” (InSpe) and participate in government procurement tenders for Personal Protection Equipment (FFP2 face masks). If you are interested in cooperation please ask for dealership application form.



    COMPANY DETAILS

    Baltic Masks, UAB
    Registration number: 305709371
    VAT code: LT100013839515
    Account No .: LT34 3500 0100 1152 5155, Paysera LT, Bank code: 35000,
    SWIFT: EVIULT21XXX Account No 2 .: LT097300010166911771, Swedbank LT,
    SWIFT: HABALT22

    +37065992104

    info@balticmasks.com